Platon Multi

Platon Multi can be dry lined on walls, screeded, or finished with a dry board system on floors; Suitable for floors in industrial buildings, it will transfer loading through screed layers to the underlying concrete floor to be upgraded* Platon Multi can be used in conjunction with other Platon membranes and the PAM Aqua Channel and Pump system* BBA Approved; 5mm PP cavity drain membrane; Fast track solution for walls or floors; Suitable for use above or below ground; Impermeable to water, gas and water vapour

Platon Plaster Base

Platon Plaster Base can be installed on internal walls and vaulted ceilings above or below ground level. The substrate remains visible through the clear membrane for precise fixing. It is suitable for use with sand and cement renders and most lightweight and renovating plasters - however please check with PAM for further product advice* BBA Approved; HDPE cavity drain membrane for direct plastering; Single component, no mesh or fabric layer; Unique undercut stud design creates mechanical key for plaster; Easy to cut, fix and seal; Impermeable to water, gas and water vapour; Compatible with other Platon membranes

Platon P5

P5 is a tough and economically priced membrane for both remedial and new build construction. It is suitable for sub-ground tanking and also for use above ground to isolate walls which are damp or contaminated with salts.* P5 can be dry lined on walls and screeded or a floating dry board system fitted on floors, and vaulted ceilings above or below ground level* Economical 5mm HDPE cavity drain membrane; Suitable for both walls and floors, above or below ground; Impermeable to water, gas and water vapour; Compatible with other Platon membranes

Platon P20

P20 is a high capacity drainage membrane recommended for use on all floor applications below ground due to its ability to control free flowing water. The deep stud profile is designed to resist blockages caused by lime deposits.* BBA Approved; Heavy duty, deep studded HDPE cavity drain membrane; Principally used on floors; For areas subject to high volume water penetration; Impermeable to water, gas and water vapour

PAM Aqua Pump System

A complete 'off the shelf' drainage system; System comprises drainage channel, sump, pump and all fittings; Suitable for use with Platon Cavity Drain membranes; The system comprises PAM Aqua Channel (a PVC drainage conduit which is fitted around the perimeter of the floor) and the PAM Aqua Pump Kit ( a mains powered submersible pump and preformed sump).; The sump is located into the floor with the removable, structural lid finishing flush with the surrounding floor level.; The submersible pump is then installed inside the sump and controlled by an automatic integral float switch.; Also available are:: a non-return valve, to avoid water backing up:, and a high level water alarm, which warms of mechanical or power failure;. A 12v Battery Back-up Pump is also available.; The sump basin is 560mm high x 460mm diameter.; The 240v pump requires wiring into a fused spur outlet within 1.5m of the pump.

PAM Aqua Channel

PAM Aqua Channel is a PVC drainage conduit designed for the control of water ingress in below ground situations. PAM Aqua Channel is fitted around the perimeter of the floor at the vulnerable floor/wall junction. PAM Aqua Channel can be used in most water proofing situations, and is particularly suited for use in conjunction with Isola Platon Cavity Drain Membrane syatems. Water entering the building throught the walls is controlled behind the Platon Membrane and diverted to the Aqua Channel at the base of the wall. The water enters the Aqua Channel through pre-drilled 19mm holes drainage holes set 70mm apart along its length and is then diverted to a suitable drainage point, either natural or a sump and mechanical pump. Jetting eyes and channel to sump connector's can also be fitted into the perimeter drainage system to enable the Qua Channel to be cleaned periodically if necessary. In situations where an existing floor slab/screed is solid and showing no signs of water ingress, cracking or de-bonding, the installation of Aqua Channel can eliminate the need for Platon Cavity Drain membrane on the floor, proving beneficial in areas of limited headroom. The application of a liquid waterproof coating to the existing floor would be recommended to act as a moisture suppressant.

Platon Double Drain (Drainage & Protection Membrane)

Platon double drain is a vertical drainage layer for external basement walls and a protection board to primary membranes.; It consists of an impermeable studded sheet, manufactured from high density polyethylene with a polypropylene filter fabric bonded to the top of the surface of the studs.; Channels between the studs form an air gap against the underlying structure.; Platon double drain forms drainage layers on both sides of the studded core sheet.; The filter fabric facing the backfill material ensures the drainage channels are not blocked or obstructed.

Plaster Base Fixing Plug

The Platon Plaster base fixing plug is made of Polymer Co Polypropylene with a length of 70mm.; It is intended for use in brick, concrete block and concrete, which is predrilled to a minimum depth 85mm from the surface of the Platon Plaster base membrane with an 8mm diameter drill bit.; The head of the Plaster base has a diameter of 35mm with an embossed surface to provide a mechanical key for subsequent plaster/render. ;The plaster base fixing plug is resistant to normally occurring chemicals in the building construction.

Platon Plaster Base Fleeceband overtape

Based on a blend of butyl and other rubbers, this non woven fabric-backed versatile strip sealant has good tack and adhesion to most common surfaces whilst having good movement accommodation.

Platon Wall/Floor Junction for Sealed System

Platon Wall/Floor Junction is manufactured from black high density polyethylene (PEH).; It is impermeable and used to provide a continuous seal between two adjacent sheets of Platon Membrane with Platon Sealing tape around external (or internal) corners in walls or similar projections.; Installation is carried out by simply folding the product along the preformed crease, and placing with the flat face towards the Platon Membrane on each adjacent wall surface.; Wall Floor junction is supplied in lengths of 2m with a preformed crease, for the fold line along the centre line.; 10 lengths rolled up together.

Platon Double Drain

Platon Double Drain 'X' Cramp is manufactured from black polyethylene.; The Double Drain 'X' Cramp fits precisely between four of Platon Double Drain's studs and therefore transmits loading from Double Drain to the nail very effectively.; It has a hole size of 3.5mm diameter.; The Double Drain to be fixed, place and fix Double Drain 'X' Cramp, then replace filter fabric.; Platon Double Drain 'X' Cramp is resistant to normally occurring chemicals in the building construction.

Platon Brick Plug 10 x 75 mm

Platon Brick Plug 10 x 75mm is a plug of polyacetal (POM) with a length of 75mm, and is intended for use in soft brick or stone, which is predrilled a minimum depth of 90mm from the surface of the Platon Membrane with a drill bit of diameter 10mm.; Platon Brick Plug has a head of diameter 30mm, which is cone shaped like the back face of the Platon Membrane's stud.; This gives an excellent transfer of loading from Membrane to the base structure.; There is a 5mm hole in the shank of the plug for fixing the next layer onto the Platon Membrane, using a screw of diameter 5 to 6mm, with screwing-in depth of max 30mm.

Non Return Valve

The Non-Return Valve is part of the PAM Aqua Pump System.

High Level Water Alarm

The High Level Water Alarm is part of the PAM Aqua Pump System.

12v Battery Back Up

The 12v Battery Back Up is part of the PAM Aqua Pump System.

Platon Wall/Floor Junction

Platon Wall/Floor Junction is manufactured from black high density polyethylene (PEH).; It is impermeable and used to provide a continuous seal between two adjacent sheets of Platon Membrane with Platon Sealing tape around external (or internal) corners in walls or similar projections.; Installation is carried out by simply folding the product along the preformed crease, and placing with the flat face towards the Platon Membrane on each adjacent wall surface.; Wall Floor junction is supplied in lengths of 2m with a preformed crease, for the fold line along the centre line.; 10 lengths rolled up together.